How do you use Cetol in the Marines?
bristle brush, smoothly, in the direction of the grain. Keep a wet edge to prevent lap marks and thoroughly saturate end grains where possible. Apply 3 coats of Cetol® Marine Natural Teak. Always allow 24 hours drying time in between coats.
How long does it take cetol Marine to dry?
Apply 3 coats of Cetol® Marine. Always allow 24 hours drying time in between coats. Sanding between coats is not recommended as this will result in a reduction of dry film thickness. Recommended film thickness must be applied to ensure effective product performance.
How do I use sikkens?
APPLICATION: When applying the first coat of Cetol, apply it at a time of day when dew, rain, or other condensation will not affect the cure or finish. The ambient air environment, Cetol product, and wood substrate must be between 50 and 90°F. Avoid applying in direct sunlight, if possible.
Do I need to sand between coats of Sikkens?
Sikkens Cetol Deck Slip Resistant Do not sand between coats. Always apply coatings along the grain and never across.
How long does sikkens take to dry?
Drying Time: Touch-dry six (6) – eight (8) hours; dry to walk on after 24 hours minimum at 68º F and 65% relative humidity. Note: During application, moisture content of wood substrate should not exceed 21%. Do not apply when rain, dew, or frost are forecast within five (5) hours of application.
How many coats does cetol Marine have?
3 coats
Apply 3 coats of Cetol® Marine. Always allow 24 hours drying time in between coats. Sanding between coats is not recommended as this will result in a reduction of dry film thickness.
How do you prepare for cetol?
Before applying Cetol, ensure that the moisture content of the wood is below 18%. Do not thin or seal the wood with any products. Apply Cetol Marine liberally, at full strength, with a long-haired bristle brush. For best results, apply by brushing Cetol in the direction of the grain.
Is sikkens cetol oil or water based?
oil-based
Sikkens Cetol HLSe is the ultimate timber coating all-rounder. A premium, oil-based, deeply penetrating and highly transparent timber stain for exterior use on decks, cladding, screening, timber joinery and furniture.
Is Sikkens oil or water based?
water based
Sikkens Cetol BLX-Pro is a quick drying water based exterior timber finish that is ideal for decks and outdoor furniture providing good durability and flexibility.
How long does sikkens cetol take to dry?
Sikkens Proluxe Cetol SRD Dry Time Drying Time – 24 hours minimum at 68°F and 65% relative humidity. At temperatures below 50º F (10º C) or conditions of high humidity the drying time will be extended. Proluxe Cetol SRD dries to touch in approximately 6 hours. Wait 24 – 48 hours for light foot traffic.
How long does it take sikkens to dry?
Do you sand between coats of Sikkens?
Is sikkens cetol water based?
Sikkens Cetol BLX-Pro is a quick drying water based exterior timber finish that is ideal for decks and outdoor furniture providing good durability and flexibility. Its highly transparent finish accentuates the natural characteristics and colour of the wood.
How long does Sikkens take to dry?
Is Sikkens cetol oil based?
Sikkens Proluxe Cetol SRD is a one coat, oil-based, transparent exterior wood finish. Sikkens Proluxe Cetol SRD was created for use on a variety of wood surfaces including siding, rails, decks, and logs. Available in a curated palette of eight wood tones.
How long does Sikkens cetol take to dry?
How long does Sikkens cetol last?
Sikkens states in their literature that you should expect to get 2-4 years life out of their system on a sunny side of a house, and 3-5 years on a shady side.